Introduction : Repairing the Rear Wheel of Wispeed SUV1000
Hello everyone and welcome to this new MoovMoov tutorial !
Today, we will guide you on how to repair a flat tyre on the rear wheel of your Wispeed SUV1000 electric scooter. We will be replacing the inner tube, and you’ll see that the repair is not very complicated!
You will simply need :
🛒 Inner tube for Wispeed SUV1000 (10×2.125 with a bent valve 70/90)
🛒 Valve extension and valve core remover
Removing the rear wheel
Let’s begin by removing the side covers on the left and right of the scooter by unscrewing the two small screws using a 3mm Allen key.
Next, we disconnect the motor’s connector by pulling on the two ends.
You can do this with your hands, but personally, I prefer to hold the right part with my finger and use pliers to pull on the connector. I find it easier that way.
Once the motor is disconnected, we can unscrew the rear wheel of our Wispeed using a 17mm wrench.
Then, slide the flat tire out by sliding it downward.
Removing the old tire and punctured inner tube
Now, we push inside the valve of the punctured inner tube to ensure there’s no air inside and to be able to unscrew the rim smoothly.
Once that’s done, we unscrew the 6 screws of the rim using a 4mm Allen key.
Now, we can lift the half-rim and pass it through the brake disc.
And we can remove the tire and inner tube from the motor.
Installing the new inner tube
We can take our new slightly inflated inner tube.
🛒 Wispeed SUV1000 Inner Tubes (10×2.125, angled valve 70/90)
Before installing the new inner tube, make sure to thoroughly check the inside of your tire to ensure there are no debris stuck inside.
Closing the rim on the motor
Next, we place the tire around the motor, inserting the valve into its housing.
Ensure that the motor is centered in the middle of the tire.
Here’s a crucial point: press on the sides of the tire and make sure that no part of the inner tube is protruding and touching the gray area. If it’s protruding and touching that area, it means the inner tube will get pinched when closing the rim.
If everything looks good, we can reattach the half-rim to the motor and tighten it securely.
Installing the wheel on the rear fork
Now, we can put the rear wheel of our Wispeed SUV1000 back onto the rear fork and tighten the two nuts on the left and right.
Connecting the motor
Next, we reconnect the motor’s connector by aligning the two arrows.
If there’s not much play in the right connector, to make it easier to insert the male connector into the female connector, you can hold the connector with pliers and push the other one inside.
Inflation and tire pressure for Wispeed
Now, we can inflate the tire to a pressure between 2.4 and 3.1 bars using an valve extension.
Finishing touches
Lastly, don’t forget to reattach and tighten the side covers on the left and right.
Products related to this tutorial
Other tutorials that may interest you
Replacing the FRONT WHEEL of a Wispeed SUV1000 Electric Scooter – Tyre and Inner Tube
How to Change the Tyre and Inner Tube on the Rear Wheel of a Wispeed Scooter? Repair Tutorial for Wispeed SUV1000 Electric Scooter – In this tutorial, we will show you how to remove your rear wheel, take off the old tire, and replace the punctured inner tube with new ones.
PURE AIR Changing the Tyre and Inner Tube – Rear Wheel
We’ll show you step by step how to change the tyre and inner tube on the rear wheel of your Pure Air electric scooter. This repair is easy, and you’ll be able to do it without any trouble!
How to disassemble the front wheel of a Xiaomi M365 Pro scooter ?
During the front tire change of your electric scooter, many of you are facing difficulties in disassembling the front wheel of your Xiaomi M365 Pro. If the nuts are tightened too tightly and you’re unable to loosen them, here are some tips to help you loosen them.